| Fix the camera
Please hang it firmly if you fix the camera at the ceiling, or it would
hurt you if it falls.
If you fix the camera with hanging frame, camera frame and attached revolvable
chassis, please do it as follows:
| ， |
Use the triangle frame and screw and screw them tightly with the
screwdriver. |
| ， |
Fix the triangle linking implement at level place. |
Attention:
| ， |
Non-professional not to open the camera cover. |
| ， |
Lay down the camera softly. |
| ， |
Don¨t put the camera at damp or easy to be rained place, or operate
it at damp place. Once it is damp, turn off the electrical source
and ask the professional for repairing, because it is easy to damage
the camera and very likely to lead electric-hit accident. |
| ， |
Don¨t use intense cleaning chemical when clean it. |
| ， |
Don¨t make the camera face to the sun. Don¨t operate it near the
spot light or other strong light or reflecting light despite indoor
or outdoor. |
inking the camera
| ， |
Link the video electric cable with VIDEO OUT socket. |
| ， |
Link the video electric cable with VIDEO IN (such as video monitoring
implement) socket. |
Attention:
This switch is used to set up the camera synchronism style, internal
or AC synchronism. The latter should only be used in AC 24V. When the
electric source is DC 12V, please choose the former style. The electric
source socket should be used in formulated electric source and voltage.
Please put the wire plug into the innermost.
| ， |
75Ω cable of same axis |
| ， |
Electric source wire |
Phase adjusting
| ， |
Vertical phase( synchronism model) |
| ， |
Picture may roll vertically if the vertical phase has not been set
up. Revolve the adjusting screw to adjust the vertical phase. |
Incidence light energy level adjusting
Owing to the incidence light energy level is preset up in the factory,
usually there is no necessary to be adjusted. But if the picture is too
dark or exposed excessively, certainly we should adjust the screw with
screwdriver, which should be only used for DC.
| ， |
Adjust it towards L (low) to make the picture darker. |
| ， |
Adjust it towards H (high) to make the picture lighter. |
Fix the automatic diaphragm lens socket
You need fix the lens socket when you use the automatic diaphragm. And
it must be fixed by certificated professional repairman or system worker.
| ， |
Excise the control cable at the edge of the lens socket in order
to take away the old one, and then strip the cable surface. |
| ， |
Weld the lens cable at the leading lens socket. |
Fix the lens
| ， |
Unload the interface cover. |
| ， |
Revolve the lens till tightly. |
| ， |
Insert the lens plug into LENS socket. (omit when fix the manual
control diaphragm lens) |
| ， |
Revolve the focal distance, adjust the screw and adjust the focal
distance according to the type of the lens. |
Warning:
Don¨t unload the interface cover from the camera if you don¨t fix the
lens.
Automatic diaphragm lens switch (DC/VIDEO)
Used in choosing the control, signal of automatic diaphragm.
DC: DC signal of controlling automatic diaphragm.
VIDEO: VIDEO signal of controlling automatic diaphragm.
When DC/VIDEO switch serves as VIDEO, BLC may be at abnormal.
| ， |
When the switch serves as VIDEO, the camera may incur hunting vibration.
At this moment, you can adjust LEVEL (L/H) on the lens to change the
incidence light energy level. |
| ， |
When you adjust the incidence light energy level, make ALC serve
as AV. |
| ， |
When the switch serves as ON, its function is to adjust the light
exposure and give supply on condition of adverse light. |
| ， |
Power |
Use DC12V& AC 24V power supply
When connection the adapter, Please connection to be right cable, the
wrong connection can cause the breakdown or damage the camera.
B,Operation & store camera
Please don¨t work in the extremely bright object the long time.
| ， |
Operating temperature: -10oC ~+50oC RH95% Max |
| ， |
Don¨t approaches moist or the extremely dust place |
| ， |
Keep away from the mechanical vibrations. |
| ， |
Don¨t anear fluorescent lamp and reflection light object. |
| ， |
Blows down on the lens with the air blower the dust, use the soft
and dry cloth cleaning the housing, if still dirty, please use the
cloth to dip the few neutral cleanser. |
| ， |
Don¨t use the ethyl alcohol,gasoline or diluent and so on volatile
the solvent otherwise can damage the varnish. |
|